smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.4.0-100-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD800AAJS-00B4A0 Serial Number: WD-WCAT21383279 LU WWN Device Id: 5 0014ee 1013931b9 Firmware Version: 01.03A01 User Capacity: 80.025.280.000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Jun 9 13:33:36 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2580) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 34) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 996 3 Spin_Up_Time 0x0027 149 138 021 Pre-fail Always - 3550 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1572 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 068 068 000 Old_age Always - 23419 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1569 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 121 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1572 194 Temperature_Celsius 0x0022 115 085 000 Old_age Always - 28 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 1 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 2 SMART Error Log Version: 1 Warning: ATA error count 688 inconsistent with error log pointer 1 ATA Error Count: 688 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 688 occurred at disk power-on lifetime: 22210 hours (925 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 01 51 00 15 57 2a e3 Error: AMNF at LBA = 0x032a5715 = 53106453 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 20 56 2a 03 00 01:03:12.430 READ DMA c8 00 00 20 55 2a 03 00 01:03:12.429 READ DMA c8 00 00 20 54 2a 03 00 01:03:12.429 READ DMA c8 00 00 20 53 2a 03 00 01:03:12.428 READ DMA ca 00 20 e0 b9 d0 04 00 01:03:12.428 WRITE DMA Error 687 occurred at disk power-on lifetime: 22210 hours (925 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 15 57 2a e3 Error: UNC at LBA = 0x032a5715 = 53106453 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 10 57 2a 03 00 01:03:08.269 READ DMA c8 00 08 08 57 2a 03 00 01:03:08.206 READ DMA e7 00 00 00 00 00 00 00 01:03:08.165 FLUSH CACHE ca 00 08 60 15 5f 00 00 01:03:08.165 WRITE DMA ca 00 01 20 22 3a 02 00 01:03:08.165 WRITE DMA Error 686 occurred at disk power-on lifetime: 22210 hours (925 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 01 51 00 15 57 2a e3 Error: AMNF at LBA = 0x032a5715 = 53106453 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 00 57 2a 03 00 01:03:04.070 READ DMA e7 00 00 00 00 00 00 00 01:03:03.935 FLUSH CACHE ca 00 08 50 15 5f 00 00 01:03:03.935 WRITE DMA ca 00 08 60 15 5f 00 00 01:03:03.934 WRITE DMA ca 00 08 a0 28 03 00 00 01:03:03.934 WRITE DMA Error 685 occurred at disk power-on lifetime: 22210 hours (925 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 01 51 00 15 57 2a e3 Error: AMNF at LBA = 0x032a5715 = 53106453 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 20 00 57 2a 03 00 01:03:00.425 READ DMA ca 00 20 e0 b9 d0 04 00 01:03:00.425 WRITE DMA ca 00 20 80 a7 24 07 00 01:03:00.425 WRITE DMA c8 00 20 e0 56 2a 03 00 01:03:00.424 READ DMA ca 00 20 e0 b9 d0 04 00 01:03:00.424 WRITE DMA Error 684 occurred at disk power-on lifetime: 22186 hours (924 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 01 51 00 15 57 2a e3 Error: AMNF at LBA = 0x032a5715 = 53106453 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 20 56 2a 03 00 02:47:50.493 READ DMA c8 00 00 20 55 2a 03 00 02:47:50.492 READ DMA c8 00 00 20 54 2a 03 00 02:47:50.492 READ DMA c8 00 00 20 53 2a 03 00 02:47:50.491 READ DMA e7 00 00 00 00 00 00 00 02:47:50.446 FLUSH CACHE SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.